MPT Engine Treatment:

If MPT Engine Treatment is so great, why don’t the engine oil companies add it?  As noted on our ZDDP page (click here), the Environmental Protection Agency has mandated the reduction of zinc in motor oils. American Petroleum Institute (API) approved oils do not have the zinc-phosphorous levels necessary to adequately reduce heat and friction for severe service (e.g. racing, emergency vehicle, or fleet service), older cars with flat tappet valves, or long-term engine use. In short, most engine oil companies will not include additives which will make it more difficult to meet the API standard while incurring additional expense.

Fuel Mileage: Independent tests have shown a fuel mileage increase of more than 5% with MPT Engine Treatment. Your actual results may vary depending on the type of driving and the condition of the car or engine. It can take up to approximately 1,000 miles for MPT Engine Treatment to coat internal engine parts and increase fuel mileage during the initial application.

Better Performance: MPT Engine Treatment will increase fuel mileage, increase performance, and extend engine life by coating internal engine parts for an extremely low surface friction.

New Car Warranty: MPT Engine Treatment will not void your new car warranty. It is perfectly safe for use in all new car and truck (diesel or gasoline) engines. Allow a minimum of 3,000-5,000 miles for break-in before adding MPT Engine Treatment.

Oil Filters: MPT Engine Treatment will not clog oil filters or become trapped anywhere inside the engine. The PTFE particles contained in MPT Engine Treatment are microscopic in size (substantially less than 1 micron which is much smaller than the width of a human hair). Most oil filters are designed to filter particles 10 microns or larger.

Synthetic Oil: MPT Engine Treatment is compatible with all synthetic and petroleum based motor oils.

Adding MPT Engine Treatment: For the initial application, we recommend adding two ounces of MPT Engine Treatment for each quart of motor oil. For subsequent applications, we recommend adding one ounce of MPT Engine Treatment per quart of motor oil.

Older Vehicles: MPT Engine Treatment can be used in older vehicles with high mileage. MPT Engine Treatment helps to fill voids created by normal wear and scaring to reduce surface friction. The result will be reduced oil burning and smoother operation. MPT Engine Treatment will not correct problems with defective seals, rings, valves, etc.

Starting: MPT Engine Treatment will help engines start more easily in warm weather. MPT Engine Treatment helps engines to run cooler and lessens the likelihood of problems associated with hot engine parts when restarting.

In cold weather, MPT Engine Treatment will help start cold engines by increasing the cranking speed. This is especially helpful when batteries weaken in frigid temperatures.

Turbos: Turbo-charged motors run extremely hot. MPT Engine Treatment helps them run cooler.

Oil Change Intervals: We recommend following the manufacturers requirements for oil change service. However, you will find that your oil will be cleaner when using MPT Engine Treatment because of the reduction in friction. Should you question the need to change the oil, there are companies available that will analyze the cleanliness for a small fee.

Motorcycles: MPT Engine Treatment can be added to all four cycle (oil and gas are NOT mixed) engines including those with wet clutches.

MPT Gear Treatment:

Better Performance: MPT Gear Treatment will increase performance, increase fuel mileage, and extend the life of all manual transmissions, differentials and transfer cases by coating internal parts for an extremely low surface friction.

Automatic Transmissions: MPT Gear Treatment is too slippery for use in automatic transmissions; therefore, it should not be added.

Manual Transmissions: MPT Gear Treatment will help manual transmissions run cooler and smoother. They will also shift more easily.

Adding MPT Gear Treatment: We recommend adding a minimum of one ounce per quart of oil. More should be added as needed, up to a maximum of six ounces of MPT Gear Treatment per quart of oil.

Differentials and Transfer Cases: MPT Gear Treatment will help all gear boxes to run cooler and smoother. MPT Gear Treatment can be added to differentials with posi-traction clutches.

MPT Twelve Lubricant and Penetrant

Applying MPT Twelve: MPT Twelve can be safely applied to door hinges, bearings, roller guides, door tracks, chains, locks, cables, etc. Use it anywhere lubrication is needed.

Deicing: With regular use, MPT Twelve will help locks perform better in freezing temperatures. For new applications, MPT Twelve will disperse ice and free frozen locks.

Motorcycles & Bicycles: MPT Twelve helps motorcycle and bicycle cables work better by allowing them to move more freely. It also provides excellent protection as a chain lube.

Protective Film: MPT Twelve leaves a protective film on applied surfaces to provide the longest lasting protection available from a lubricant or penetrant.